You may do this by typing its IP address directly into your browser’s URL.
For help, please see How To Discover A Room Alert Monitor<\/a> & How To Open Your Room Alert Monitor\u2019s Built-in Web Interface<\/a>.<\/li>\n\n\n\n
For help, please see How To Access A Room Alert Monitor\u2019s Password-Protected Pages<\/a>.<\/li>\n\n\n\n
![\"\"](\"https:\/\/avtech.com\/articles\/wp-content\/uploads\/2025\/05\/MAX_NavMenu-SensorConn.png\")
<\/li>\n\n\n\n![\"\"](\"https:\/\/avtech.com\/articles\/wp-content\/uploads\/2025\/05\/MAX_SensorConn-Default.png\")
<\/li>\n\n\n\n![\"\"](\"https:\/\/avtech.com\/articles\/wp-content\/uploads\/2025\/05\/MAX_SensorConn-PairModal1.png\")
\n- \n
- This 6-digit PIN can be found on the unit’s sticker.\n
- \n
- For Wireless Temperature\/Humidity sensors, this sticker is located inside the sensor’s battery compartment.<\/li>\n\n\n\n
- For Wired Sensor Adapters, this sticker is located on the bottom of the unit.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n\n\n\n
- Click Next<\/strong>. The modal will progress to the next set of instructions.
![\"\"](\"https:\/\/avtech.com\/articles\/wp-content\/uploads\/2025\/05\/MAX_SensorConn-PairModal2.png\")
<\/li>\n\n\n\n- Then, press the PAIR button on the bottom\/back of the sensor\/adapter to put it into Pairing mode.\n
- \n
- You’ll know its in Pairing Mode when you see its LED begin to steadily blink.<\/li>\n<\/ul>\n<\/li>\n<\/ol>\n\n\n\n
You’ll know its in Pairing Mode when you see \t\t
- \n
- Once the unit is in Pairing Mode, click Pair<\/strong>.<\/li>\n\n\n\n
- Your Base Station should discover the unit and pair with it.
![\"\"](\"https:\/\/avtech.com\/articles\/wp-content\/uploads\/2025\/05\/MAX_SensorConn-PairModal3.png\")
<\/li>\n\n\n\n- You’ll see the unit’s name (the last 4 digits of its MAC, by default) appear in the list. A sensor\/adapter placeholder will immediately appear in the Readings <\/em>page; it may take a minute to load initial data.<\/li>\n<\/ol>\n\n\n\n
Troubleshooting<\/h2>\n\n\n\n
If you’re having trouble pairing a sensor or Wired Sensor Adapter, it’s possible that the device is stuck in bonded mode. To check:<\/p>\n\n\n\n
- \n
- First, power-cycle the device\u2014either by unplugging its power adapter and\/or removing its batteries for a couple seconds.<\/li>\n\n\n\n
- Upon replacing the power adapter and\/or batteries, the device’s LED will indicate its bonded status:\n
- \n
- A single LED flash = the device is not bonded<\/li>\n\n\n\n
- 2 LED flashes = the device is bonded<\/li>\n<\/ul>\n<\/li>\n<\/ol>\n\n\n\n
You can see an \t\t
- \n
- If the device’s status is bonded, you may reset it by holding-in its PAIR <\/strong>button until you see 3 rapid flashes, then release. \n
- \n
- This means the bond has cleared.<\/li>\n<\/ul>\n<\/li>\n<\/ol>\n\n\n\n
You can see an \t\t
- \n
- Retry the pairing process with your Base Station.<\/li>\n<\/ol>\n\n\n\n
If you continue to have trouble pairing the sensor (or Wired Sensor Adapter), try bringing it closer to the Base Station.<\/p>\n\n\n\n
Forget Sensor<\/h2>\n\n\n\n
Follow these steps to unpair a wireless sensor or Wired Sensor Adapter from your MAX Base Station:<\/p>\n\n\n\n
- \n
- First, open the Base Station’s web interface.
You may do this by typing its IP address directly into your browser’s URL.
For help, please see How To Discover A Room Alert Monitor<\/a> & How To Open Your Room Alert Monitor\u2019s Built-in Web Interface<\/a>.<\/li>\n\n\n\n- Log In to the web interface.
For help, please see How To Access A Room Alert Monitor\u2019s Password-Protected Pages<\/a>.<\/li>\n\n\n\n- Navigate to Settings<\/strong> \u2192 Sensor Connections<\/strong>.
<\/li>\n\n\n\n- In the list of paired sensors and adapters, locate the unit you wish to unpair.<\/li>\n\n\n\n
- Select the ellipses beside the desired unit, and then choose Forget<\/strong>.
![\"\"](\"https:\/\/avtech.com\/articles\/wp-content\/uploads\/2025\/05\/MAX_SensorConn-Forget.png\")
<\/li>\n<\/ol>\n\n\n\n\n\n\n","protected":false},"excerpt":{"rendered":"Pairing Follow these steps to pair a wireless sensor or Wired Sensor Adapter to your MAX Base Station: You’ll know its in Pairing Mode when you see . Troubleshooting If you’re having trouble pairing a sensor or Wired Sensor Adapter, it’s possible that the device is stuck in bonded mode. To check: You can see […]<\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"ngg_post_thumbnail":0},"categories":[349,2],"tags":[],"yoast_head":"\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\t\n\t\n\t\n
- Log In to the web interface.
- First, open the Base Station’s web interface.
- Retry the pairing process with your Base Station.<\/li>\n<\/ol>\n\n\n\n
- This means the bond has cleared.<\/li>\n<\/ul>\n<\/li>\n<\/ol>\n\n\n\n
- If the device’s status is bonded, you may reset it by holding-in its PAIR <\/strong>button until you see 3 rapid flashes, then release. \n
- Your Base Station should discover the unit and pair with it.
- Once the unit is in Pairing Mode, click Pair<\/strong>.<\/li>\n\n\n\n
- Then, press the PAIR button on the bottom\/back of the sensor\/adapter to put it into Pairing mode.\n